MODEL COLOR MODEL NUMBER Topaz mist metallic 1503 HO (255 HP) 189A, 189B Bright yellow GTX Limited iS ENGINE 1503 HO (255 HP) 349A, 349B RXT iS The information and component/system descriptions
#SEADOO VTS BUTTON COVER HOW DO YOU REMOVE THE BUTTON COVER MANUAL#
INTRODUCTION INTRODUCTION This shop manual covers the following BRP made 2009 Sea-Doo watercraft models. This edition was primarily published to be used by watercraft mechanical technicians who are already familiar with all SAFETY NOTICE SAFETY NOTICE This manual has been prepared as a guide to correctly service and repair 2009 Sea-Doo® watercraft as describe in the model list in the INTRODUCTION. TABLE OF CONTENTS 07 BODY AND HULL (cont’d) 02 – BODY (cont’d) PROCEDURES (cont’d) STORAGE COMPARTMENT COVER. TABLE OF CONTENTS 06 STEERING AND PROPULSION (cont’d) 03 – JET PUMP. TABLE OF CONTENTS 05 ELECTRICAL SYSTEM (cont’d) 06 – DIGITALLY ENCODED SECURITY SYSTEM (D.E.S.S.) (cont’d) PROCEDURES (cont’d) D.E.S.S. TABLE OF CONTENTS 04 FUEL SYSTEM (cont’d) 03 – FUEL TANK AND FUEL PUMP (cont’d) PROCEDURES (cont’d) FUEL LEVEL SENSOR.
![seadoo vts button cover how do you remove the button cover seadoo vts button cover how do you remove the button cover](https://i.ebayimg.com/thumbs/images/g/~~sAAOSwtGlZJMHP/s-l225.jpg)
TABLE OF CONTENTS 03 ELECTRONIC MANAGEMENT SYSTEMS (cont’d) 03 – COMMUNICATION TOOLS AND B.U.D.S. TABLE OF CONTENTS 02 ENGINE (cont’d) 09 – COOLING SYSTEM. TABLE OF CONTENTS 02 ENGINE (cont’d) 04 – SUPERCHARGER (cont’d) TROUBLESHOOTING. (BRP) © Bombardier Recreational Products Inc. No parts of this manual may be reproduced in any form without the prior written permission of Bombardier Recreational Products Inc. Legal deposit: National Library of Quebec National Library of Canada 2009 All rights reserved. If each of the gauge button indicator lights come on when the applicable switch is pressed, the problem may be related to the information center.Ģ009 Shop Manual RXT® iS™ 255 GTX† LIMITED iS™ 255 SWITCH INPUTS 1. MODE/SET and UP/DOWN arrow button indicator lights NOTE: You will need to press the START button every three minutes or the electrical system will shut off.Ĥ. Choose the Monitoring tab at the top of theĥ. At the bottom LH side of the monitoring page,ġ. Read Data button 2. Monitoring tab 3. Cluster tab 4. Switch inputs fieldĦ. Press each of the MODE/SET and UP/DOWNĪrrow buttons and look for the applicable indica- tor light to come on in the Switch inputs field on lower RH side of the cluster page (Mode , Set , UP or Down). MODE/SET and UP/DOWN Arrow Buttons Test Using B.U.D.S.ġ. Connect the watercraft to the latest B.U.D.S.Ģ. Press the START/STOP button to energize the NOTE: The above stated voltages vary slightly de- pending on the actual voltage applied to the circuit and the current flow through the diodes. When using a Fluke 115 multimeter for testing in diode test mode, the voltage and current applied by the multimeter are lower than in circuit. The quality of probe contact, the actual probes and leads, and the precision of the meter calibration will all affect the results, which will most likely be slightly lower than nominal values stated. The information center will use the signals from the switches and the transmitted information from the other modules, convert them to an in- dication, and cancel the command signal it sent out once the function has been carried out.Ĭommand signals from the MODE and SET switches are used by the information center only. VTS and iS switch commands are translate and sent to the modules. The UP/DOWN arrow switch commands are used by the gauge for cer- tain functions and settings only. The UP/DOWN button command signals will also be translated and sent out through the CAN bus to be used by the ECM for the CRUISE and SLOW SPEED func- tions (increasing or decreasing speed when the functions are active), and by the iBR for iBR gate positioning in SLOW SPEED mode of operation.
![seadoo vts button cover how do you remove the button cover seadoo vts button cover how do you remove the button cover](https://i5.walmartimages.com/asr/da6914a0-66b8-4248-8a8e-264116ef2a7e_1.946f4e88bb6f1e114372d5576ad2478b.jpeg)
If the command generated by the closure of a switch concerns another module, a circuit within the gauge will translate it to CAN protocol and transmit it through the CAN bus. The applicable module will react to the command, carry out the function, and transmit the result back through the CAN bus. The gauge senses these voltages through pin 17 of the gauge connector, and interprets them as signals that tell it which switch is activated. The same is true for the UP/DOWN arrow switches, iS switches and VTS switches on their respective circuits. The remaining three diodes in the circuit drop 1.8 Vdc (at pin B). If the SET switch is pressed, 1 diode is bypassed.
![seadoo vts button cover how do you remove the button cover seadoo vts button cover how do you remove the button cover](https://m.media-amazon.com/images/I/6106dNlE1KL._AC_SX569_.jpg)
![seadoo vts button cover how do you remove the button cover seadoo vts button cover how do you remove the button cover](https://www.picclickimg.com/d/l400/pict/252502584187_/SeaDoo-XP-LTD-RX-LRV-GTX-GSX-RFI.jpg)
If the MODE switch is pressed, 2 diodes are by- passed. The remaining two diodes in the circuit drop 1.2 Vdc (at pin B). Section 05 ELECTRICAL SYSTEM Subsection 07 (GAUGE)